![logitech wingman joystick extreme digital 3d logitech wingman joystick extreme digital 3d](https://i.ytimg.com/vi/DOE90OBOkGI/hqdefault.jpg)
- #Logitech wingman joystick extreme digital 3d full
- #Logitech wingman joystick extreme digital 3d pro
- #Logitech wingman joystick extreme digital 3d simulator
This caused a lot of little pieces of rubber to be all inside of my joystick. Set the base upside down on top of a magazine or book and be careful not to stretch the wires. Lift the silver base up and lightly slip it over the spine while threading the upper button pad through the hole. Just let it hang off to the side for now, you'll put it back on later. Now your Twist Axis Sensor is fixed! You should be getting really excited right about now. Turns out, it worked!! Lightly turn it back and forth a few times being very careful not to break it.
#Logitech wingman joystick extreme digital 3d full
I thought, maybe by twisting it back and forth through its full range of motion a couple of times, whatever is causing the erratic readings might get cleaned up. I think that because it gets a little greasy from the factory, and because it only gets turned so far back and forth, grease or dust may build up in those two spots and mess with the readings. The joystick only uses about 1/3 of the range of the sensor. Well, I looked into this and turns out I was right. The first thing I suspected when I took this out is that the sensor actually has more range than the joystick uses. Notice that the bottom part spins around but only goes so far each way. Use a tiny bit of rubbing alcohol on a paper towel or rag and lightly clean the bottom of it. Apply pressure on opposite sides of the bottom of it with the left and right tips of your needle nosed pliers and pop it out. See that little rectangle on the top of the stick with the wiring harness coming out of it? As you can see, it looked a little dirty. I slid the trigger button off of the left side of the handle, cleaned the axle, and put bushing grease on it. Don't worry about the top part hanging down, it is not going anywhere. Now, pull the left and right pieces apart. To disassemble the handle use your thumbnail to release the little locking tab on the bottom of it. They are all identical except for the tiny one.ĭon't forget the 2 on the bottom of the handle. Go ahead and take all the screws out and put them in a safe place. Best to do it first so you don't take all the rest out to find you don't have a small enough Phillips head to reach this one. Now it's Unscrew Time! Start with the tiny screw on the very top right of the stick. You’re going to need to tape up button 2 on the joystick because it'll annoy you when putting this thing back together if you don't.
![logitech wingman joystick extreme digital 3d logitech wingman joystick extreme digital 3d](https://image.invaluable.com/housePhotos/Aether/02/677602/H22451-L216176467.jpg)
These can maybe lose tensile strength over time but mine seems brand new. Note: I Have completely disassembled mine and most of the pics may have more stuff taken off than is necessary for that part of the maintenance.īy the way, after taking mine apart, I found there are really only a few parts that wear out The spring for the actual stick (x and y axis) and the spring for twisting the stick (z axis). Thick Grease/Lube (I used Bushing Grease) Here is a tutorial on fixing that problem once and for all.Īttempt At Own Risk, Don't Lose Anything! Regardless of how many times you calibrate it, it keeps outputting incorrectly.
#Logitech wingman joystick extreme digital 3d pro
If you have a Logitech Extreme 3D Pro joystick, and you've been using it a lot, it may begin to act like it is out of calibration.
#Logitech wingman joystick extreme digital 3d simulator
This stick may be fine for some fast-paced "shoot 'em up" game, but it's worthless for Flight Simulator IMO.Logitech Extreme 3D Pro Joystick Repair Help
![logitech wingman joystick extreme digital 3d logitech wingman joystick extreme digital 3d](https://i5.walmartimages.com/asr/e187f2c7-ffe9-40c7-ba2d-6aa4d917d806_1.85ba9a061645dc44b102580299f96488.jpeg)
There's no way to disable the "sleep" function, believe me I've tried. By then you're so messed up you may as well CTRL+C your way out and go have a beer. During this 20 seconds, it sends freaky signals to the sim, like full left aileron or down elevator or something so you get to watch your beautiful approach get absolutely trashed by the stupid stick for 20 seconds and you can't do a thing about it until the stick becomes active again. You must click a button to "wake it up" and sometimes it may take up to 20 seconds to connect and become operative again. It also has a "sleep" function, where the stick "goes to sleep" after about a minute of inactivity apparently to save batteries. The elevator axis "lurches" one way or the other with very slight movements around neutral lately, getting worse by the minute. I'm currently using the "Freedom 2.4" wireless stick and it sux. I've spent my last penny on anything Logitech makes.